Solid Plasterer – ANZSCO 333212
- Solid Plasterers apply decorative and protective coverings of plaster, cement and similar materials to the interiors and exteriors of structures.
- Skill Level
Skills Assessment Requirement
Unless you are exempt in very limited circumstances, you are required to have a positive Skills Assessment to apply for the visas listed above.
Skills Assessment authority for Solid Plasterers is Trades Recognition Australia (TRA). To have a positive skills assessment, you must meet the following criteria:
- Must have successfully completed an AQF Qualification either a Certificate III in Solid Plastering or formal training that is comparable
- Must possess skills that are current to Australian industry standards demonstrated by 12 months full time employment or equivalent part-time in the occupation in the previous three years
- If you have obtained a qualification internationally or an Australian qualification that was not through the Australian Recognition of Learning process, you are required to demonstrate 3 years full time or equivalent post-qualification experience
- If you have obtained an Australian qualification issued through the Australian Recognition of Learning process, you are required to demonstrate 3 years full-time or equivalent post-qualification experience OR 6 years full-time or equivalent experience which can be either pre- or post-qualification
Potential Visa Pathways for Solid Plasterer
|ANZSCO||Occupation||Skills Assessment||189||190||485||491 (State)||491 (Family)||186 (Direct)||407 (Training)||494 (regional Sponsored)||482 (TSS Medium
Group: 3332 Plasterers
- Apply and fix plasterboard partitions, suspended ceilings, fire rating systems, acoustic tiles, and composite wall linings to buildings, and apply decorative and protective coverings of plaster, cement and similar materials to the interiors and exteriors of structures.
- Determining plasterboard layout, and installing insulation and vapour barriers
- Measuring, marking and cutting plasterboard, lifting and positioning panels, and securing them to walls, ceilings and battens
- Preparing corner beads and securing them in position
- Fixing pre-cast cornices, panel mouldings, ceiling centres and other plaster fittings
- Covering joins and nail holes with wet plaster and sealing compounds, and smoothing them using wet brushes and sand paper
- Mixing and applying coats of plaster, cement and render to structures using trowels, and levelling and smoothing coats to uniform thickness
- Plumbing and straightening corners, angles and wall and ceiling surfaces
- Creating decorative textures in finishing coats
- Applying and finishing acoustic, insulating and fireproofing materials bonded with plaster, plastic cement and similar materials
- Skill Level
- Most occupations in this unit group have a level of skill commensurate with the qualifications and experience outlined below.
AQF Certificate III including at least two years of on-the-job training, or AQF Certificate IV (ANZSCO Skill Level 3)
In New Zealand:
NZ Register Level 4 qualification (ANZSCO Skill Level 3)
At least three years of relevant experience may substitute for the formal qualifications listed above. In some instances relevant experience and/or on-the-job training may be required in addition to the formal qualification.
Registration or licensing may be required.
- Occupations in this Group
- 333211 Fibrous Plasterer
- 333212 Solid Plasterer
How to calculate your points (skilled visas)
To apply for a skilled visa, you need to know how many points you can score. The minimum score to be eligible for application is 65 points. However, depending on your occupation, the competitiveness, and the states you are applying to, you might need to score more points to get an invite.
Points will be given to you based on the following:
- Educational Qualifications
- Points for Professional Year
- Points for NAATI- Credentialled Community Language
- Points for 2 Year Study
- Points for English
- Points for Regional Study
- Points for Work Experience
- Points for Specialist Educational Qualifications (STEM)
- Points for Partner
Click here to calculate your points.
This 189 visa allows you to live, work and study in Australia permanently. It is a points-tested visa. The minimum score to apply is 65 points. However, based on previous invitation rounds, you would need to achieve a higher score to have a better chance of obtaining an invitation.
In short, to be eligible for visa 189, you need to meet the following criteria:
Subclass 190 visa– Skilled Nominated Visa & Subclass 491 visa – Skilled Work Regional (Provisional) Visa
To apply for visa subclass 190 and visa subclass 491, you need to have a nomination from the state/territory government where you want to live and work. Each State and Territory have individual requirements that must be met in order to receive nomination. (See below)
Another difference between the 190 and 491 visa is that you can only apply for visa subclass 491 if you are living and working in regional areas in Australia, while it is not a requirement if you are applying for the 190 visa.
In summary, to be eligible for 190 visa, you need to meet the following criteria:
To check if the state/ territory government requirements for your occupation, refer to the following links
Links to requirements
|New South Wales||
|Australian Capital Territory (ACT)|
The 485 visa is a work visa available to international students who have completed two years of study in Australia. It is an 18-month visa that has full work rights and full study rights. It also allows you to travel freely to and from Australia throughout the validity of the visa.
To be eligible for visa 485, you need to meet the following criteria:
If you have an employer who is willing to sponsor you, you may be eligible for a Subclass 186 visa. This visa is permanent and will allow you to live, work and study in Australia indefinitely. To be eligible for this visa, you need to have at least 3 years of working experience in your nominated occupation and a positive skills assessment. Alternatively, if you are a holder of a Subclass 457 or TSS visa, you can apply for Subclass 186 after working for your employer for at least 3 years under the Temporary Residence Transition stream.
The 407 visa a short stay visa for individuals to participate in occupational training or professional development in Australia. This visa is generally valid to stay in Australia for 2 years. Please note this visa is subject to condition 8102 which forbids work apart from the training that is specified in the visa application. You are also required to maintain health insurance whilst in Australia.
To be eligible for visa 407, you need to meet the following criteria:
You can apply for subclass 494 if you have a regional employer who is willing to sponsor you. To be eligible for this visa, you must have at least 3 years of working experience in your nominated occupation and have a relevant skills assessment. With this visa, there is a requirement that you must work for the employer who is sponsoring you.
This visa provides pathway to permanent residency through the 191 visa.
The Subclass 482 visa is a Temporary Skill Shortage visa that requires a sponsorship from an Australian employer. This visa allows to your live and work in Australia for up to 4 years. You may apply for as many 482 visas as you want, as long as the employer is willing to sponsor you.
Study Pathway to Solid Plasterer
Solid Plasterers apply decorative and protective coverings of plaster, cement and similar materials to the interiors and exteriors of structures. To become a solid plasterer, you usually have to complete an apprenticeship. You can work as a Solid Plasterer without formal qualifications, however, a certificate III in solid plastering will be useful. Entry requirements may vary, but employers generally require Year 10. It should be noted that registration or licensing may be required.
Certificate III in Solid Plastering
- Duration: 2 years
- Total Course Cost Approx: $28,500 AUD
- Completion of Australian Year 11 of equivalent
- English proficiency requirement – IELTS 5.0 overall or equivalent
- Certificate in Wall and Floor Lining
- Diploma or Certificate in Carpentry and Joinery
- Certificate III in Stonemasonry